Pump Systems<\/span><\/h2>\n\u2022 Tanker unloading system:
\nConsisting of a 20,000 L\/h motor pump with a three-phase motor III x 400Vca – 50 Hz of 3 KW and P55 – EExeIIBT4 protection, by-pass, gearbox at 430 r.p.m.; filter and retention valve. Everything was mounted on a steel frame.
\n\u2022 Pump supply system:
\nSupply to the engine bench is done by a pump system consisting of two explosion-proof motor pumps with three-phase motor III x 400Vca – 50Hz at 2.2 KW and EExeIIBT4 – IP55 protection capable of supplying 4,500 L\/h each at a 7.5 bar pressure. These motor pumps were mounted on a steel frame with spill tray and detection by capacitance probe. The unit has: Filter, by-pass, retention valves, minimum pressure switch to block the unit and avoid no-load operation, manometer, safety valve with exhaust lines and shut-off valves.
\nOn the return line, a regulation and stabilization valve is installed, adapted to the operating conditions.<\/p>\n
Control Panels<\/span><\/h2>\nThe control panel manages both the unloading system of the tanker and the pump system for the fuel ring; this is installed outside the danger zone.
\nOperations:
\n\u2022 Tanker unloading system:
\n– The system is operated with a go – stop switch (local and remote)
\n– As overfilling protection, a maximum level pump stop was planned as well as the required thermal protection in the engine.
\n\u2022 Pump system – Ring system:
\n– A rotating commuter serves to select the operation mode of the system. (Off \u2013 Automatic – Manual Pump 1 \u2013 Manual Pump 2)
\n– In Automatic mode the pumps alternate, so each pump works for 10 minutes. If the thermal protection of one of the engines is triggered, the other motor pump starts operating automatically.
\n– In Manual mode, Pump 1-2, this does not happen.
\n– If pressure drops below the established value in the minimum pressure switch regulator for any reason, the system gets locked to protect the pumps from no-load operation. Pumps keep working during those 5 seconds, in case the issue was an occasional excessive consumption; if pressure does not go up, the unit stops and must be manually reassembled.
\n– The pump system is fastened with the testing benches, so the pumping process only occurs if there are operating reactors.
\n– System interruption due to spillage is planned for (intrinsic safety), so if any leak is detected on the tray, the pump system stops.<\/p>\n
Elements of the installation supplied by INPRO<\/h3>\nLEVEL SWITCH<\/span><\/h2>\nSMMR level switches perform the operations required for the filling process and the tank overfilling alarms and protocols. Custom manufacture based on actual needs.
\n\u2022 Probes manufactured from different materials to work with fluids such as gas oil, oil, water, milk, etc.
\n\u2022 Probe with sealed head, can be fastened with 2\u2019\u2019, 11\/2\u2019\u2019 or 1\u2019\u2019 nuts, mounted with aluminum or standardized flange.
\n\u2022 For controlling pumps, solenoid valves, alarms, etc…
\n\u2022 Control box with relays and power supply.<\/p>\n
![\"\"](\"https:\/\/www.inprord.com\/imagenes\/proyectos\/p5\/1.jpg\")
<\/span><\/p>\nTRANSFER PUMP<\/span><\/h2>\nPump with self-adjusting blades, with positive movement and constant flow. Silent, robust and high-performance. Particularly recommended for transfer of all kinds of liquid -as long as they are not abrasive nor contain suspended solid particles.
\n\u2022 Blade adjustment is due to three variables. Centrifugal force, fluid pressure and push rods, so losses and turbulence are greatly decreased.
\n\u2022 Adjustable safety valve included in pump body.
\n\u2022 Pump body in cast or stainless steel, based on needs.
\n\u2022 Bench from gray cast iron.
\n\u2022 Three-phase engine with Atex certificate.
\n\u2022 Possibility of 2 rotation directions by placing an inverter.
\n\u2022 The power of the associated motor prevents possible problems at launch with low temperature fuel.<\/p>\n
![\"\"](\"https:\/\/www.inprord.com\/imagenes\/proyectos\/p5\/2.jpg\")
<\/span><\/p>\nPump unit \u201cINPRO\u201d FP GET<\/span><\/h2>\nCompact pump unit for gas oil pumping. Contains all the elements required for the proper operation of motor pumps in one bench.
\n\u2022 Gear electric pumps with three-phase or mono-phase supply.
\n\u2022 Motor protection IP-55
\n\u2022 System to interrupt no-load operation in case of lack of fuel
\n\u2022 Alternative electronic control management system v
\n\u2022 Vacumeter
\n\u2022 Aluminum filter, Retention valves.
\n\u2022 Safety valve with exhaust line.<\/p>\n
![\"\"](\"https:\/\/www.inprord.com\/imagenes\/proyectos\/p5\/3.jpg\")
<\/span><\/p>\nKerosene Unit<\/span><\/h2>\n\u2022 Digital output for incidence control from central position in kit 3, 4 and 6 signals (2-thermal, 2-motors OK, low pressure and spillage).
\n\u2022 Launch scheduling kit due to lack of current.
\n\u2022 GSM alarm system via SMS messages or modem connection.
\n\u2022 Line pressure switch for low pressure signal.
\n\u2022 Modifications for adapting tropicalized and ATEX units.
\n\u2022 Spill collector trays with infrared detectors.
\n\u2022 There are supply system versions for other fluids such as light fuel, methanol, gasoline, etc…<\/p>\n
![\"\"](\"https:\/\/www.inprord.com\/imagenes\/proyectos\/p5\/4.jpg\")
<\/span><\/p>\nCOLLECTOR TRAY WITH SPILLAGE DETECTOR<\/span><\/h2>\nPlacing collector trays under certain elements of the installation is recommended. Particularly, equipment that could leak due to its characteristics or during maintenance tasks. Placing a spillage detector for the tray gives the possibility of creating protocols.
\n\u2022 Furnace-painted plate tray with the appropriate size for each circumstance.
\n\u2022 Spillage detector in the control panel and detection probe. Infrared optical sensor for oil and water, conductivity sensor for water or both, mounted on the same probe.
\n\u2022 Standard 1.5 m probe.
\n\u2022 The control unit of the detector is mounted in a box with impact-resistant plastic cover. The control unit contains two voltage free relays, one for commuting and the other one usually open.<\/p>\n
![\"\"](\"https:\/\/www.inprord.com\/imagenes\/proyectos\/p5\/5.jpg\")
<\/span><\/p>\nPRESSURE REGULATOR VALVE<\/span><\/h2>\nConstant pressure and flow regulator valve according to consumption variations
\n\u2022 For gas oil, lubricant and hydraulic oils.
\n\u2022 Maximum temperature of the fluid: 250\u00baC.
\n\u2022 Hydraulic cast iron. Piston, needle and tempered steel spring.<\/p>\n
![\"\"](\"https:\/\/www.inprord.com\/imagenes\/proyectos\/p5\/6.jpg\")
<\/span><\/p>\n","protected":false},"excerpt":{"rendered":"The next project required automated supply of JET-A1 aircraft fuel for testing engines in bench. In this process, the unloading process of the tanker to the main tank had to be monitored and managed, with the help of an unloading pump. But the main challenge of the project were the operating supply requirements in aircraft […]<\/p>\n","protected":false},"featured_media":7567,"menu_order":0,"template":"","meta":{"_acf_changed":false,"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":"","footnotes":""},"area_proyectos":[230],"class_list":["post-6903","proyecto","type-proyecto","status-publish","has-post-thumbnail","hentry","area_proyectos-industry-chp-power-plants-water-treatment-plants-industry-bespoke-solutions"],"acf":[],"_links":{"self":[{"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/proyecto\/6903","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/proyecto"}],"about":[{"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/types\/proyecto"}],"version-history":[{"count":0,"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/proyecto\/6903\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/media\/7567"}],"wp:attachment":[{"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/media?parent=6903"}],"wp:term":[{"taxonomy":"area_proyectos","embeddable":true,"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/area_proyectos?post=6903"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}
\nConsisting of a 20,000 L\/h motor pump with a three-phase motor III x 400Vca – 50 Hz of 3 KW and P55 – EExeIIBT4 protection, by-pass, gearbox at 430 r.p.m.; filter and retention valve. Everything was mounted on a steel frame.
\n\u2022 Pump supply system:
\nSupply to the engine bench is done by a pump system consisting of two explosion-proof motor pumps with three-phase motor III x 400Vca – 50Hz at 2.2 KW and EExeIIBT4 – IP55 protection capable of supplying 4,500 L\/h each at a 7.5 bar pressure. These motor pumps were mounted on a steel frame with spill tray and detection by capacitance probe. The unit has: Filter, by-pass, retention valves, minimum pressure switch to block the unit and avoid no-load operation, manometer, safety valve with exhaust lines and shut-off valves.
\nOn the return line, a regulation and stabilization valve is installed, adapted to the operating conditions.<\/p>\n
The control panel manages both the unloading system of the tanker and the pump system for the fuel ring; this is installed outside the danger zone.
\nOperations:
\n\u2022 Tanker unloading system:
\n– The system is operated with a go – stop switch (local and remote)
\n– As overfilling protection, a maximum level pump stop was planned as well as the required thermal protection in the engine.
\n\u2022 Pump system – Ring system:
\n– A rotating commuter serves to select the operation mode of the system. (Off \u2013 Automatic – Manual Pump 1 \u2013 Manual Pump 2)
\n– In Automatic mode the pumps alternate, so each pump works for 10 minutes. If the thermal protection of one of the engines is triggered, the other motor pump starts operating automatically.
\n– In Manual mode, Pump 1-2, this does not happen.
\n– If pressure drops below the established value in the minimum pressure switch regulator for any reason, the system gets locked to protect the pumps from no-load operation. Pumps keep working during those 5 seconds, in case the issue was an occasional excessive consumption; if pressure does not go up, the unit stops and must be manually reassembled.
\n– The pump system is fastened with the testing benches, so the pumping process only occurs if there are operating reactors.
\n– System interruption due to spillage is planned for (intrinsic safety), so if any leak is detected on the tray, the pump system stops.<\/p>\n
Elements of the installation supplied by INPRO<\/h3>\nLEVEL SWITCH<\/span><\/h2>\nSMMR level switches perform the operations required for the filling process and the tank overfilling alarms and protocols. Custom manufacture based on actual needs.
\n\u2022 Probes manufactured from different materials to work with fluids such as gas oil, oil, water, milk, etc.
\n\u2022 Probe with sealed head, can be fastened with 2\u2019\u2019, 11\/2\u2019\u2019 or 1\u2019\u2019 nuts, mounted with aluminum or standardized flange.
\n\u2022 For controlling pumps, solenoid valves, alarms, etc…
\n\u2022 Control box with relays and power supply.<\/p>\n
<\/span><\/p>\nTRANSFER PUMP<\/span><\/h2>\nPump with self-adjusting blades, with positive movement and constant flow. Silent, robust and high-performance. Particularly recommended for transfer of all kinds of liquid -as long as they are not abrasive nor contain suspended solid particles.
\n\u2022 Blade adjustment is due to three variables. Centrifugal force, fluid pressure and push rods, so losses and turbulence are greatly decreased.
\n\u2022 Adjustable safety valve included in pump body.
\n\u2022 Pump body in cast or stainless steel, based on needs.
\n\u2022 Bench from gray cast iron.
\n\u2022 Three-phase engine with Atex certificate.
\n\u2022 Possibility of 2 rotation directions by placing an inverter.
\n\u2022 The power of the associated motor prevents possible problems at launch with low temperature fuel.<\/p>\n
<\/span><\/p>\nPump unit \u201cINPRO\u201d FP GET<\/span><\/h2>\nCompact pump unit for gas oil pumping. Contains all the elements required for the proper operation of motor pumps in one bench.
\n\u2022 Gear electric pumps with three-phase or mono-phase supply.
\n\u2022 Motor protection IP-55
\n\u2022 System to interrupt no-load operation in case of lack of fuel
\n\u2022 Alternative electronic control management system v
\n\u2022 Vacumeter
\n\u2022 Aluminum filter, Retention valves.
\n\u2022 Safety valve with exhaust line.<\/p>\n
<\/span><\/p>\nKerosene Unit<\/span><\/h2>\n\u2022 Digital output for incidence control from central position in kit 3, 4 and 6 signals (2-thermal, 2-motors OK, low pressure and spillage).
\n\u2022 Launch scheduling kit due to lack of current.
\n\u2022 GSM alarm system via SMS messages or modem connection.
\n\u2022 Line pressure switch for low pressure signal.
\n\u2022 Modifications for adapting tropicalized and ATEX units.
\n\u2022 Spill collector trays with infrared detectors.
\n\u2022 There are supply system versions for other fluids such as light fuel, methanol, gasoline, etc…<\/p>\n
<\/span><\/p>\nCOLLECTOR TRAY WITH SPILLAGE DETECTOR<\/span><\/h2>\nPlacing collector trays under certain elements of the installation is recommended. Particularly, equipment that could leak due to its characteristics or during maintenance tasks. Placing a spillage detector for the tray gives the possibility of creating protocols.
\n\u2022 Furnace-painted plate tray with the appropriate size for each circumstance.
\n\u2022 Spillage detector in the control panel and detection probe. Infrared optical sensor for oil and water, conductivity sensor for water or both, mounted on the same probe.
\n\u2022 Standard 1.5 m probe.
\n\u2022 The control unit of the detector is mounted in a box with impact-resistant plastic cover. The control unit contains two voltage free relays, one for commuting and the other one usually open.<\/p>\n
<\/span><\/p>\nPRESSURE REGULATOR VALVE<\/span><\/h2>\nConstant pressure and flow regulator valve according to consumption variations
\n\u2022 For gas oil, lubricant and hydraulic oils.
\n\u2022 Maximum temperature of the fluid: 250\u00baC.
\n\u2022 Hydraulic cast iron. Piston, needle and tempered steel spring.<\/p>\n
<\/span><\/p>\n","protected":false},"excerpt":{"rendered":"The next project required automated supply of JET-A1 aircraft fuel for testing engines in bench. In this process, the unloading process of the tanker to the main tank had to be monitored and managed, with the help of an unloading pump. But the main challenge of the project were the operating supply requirements in aircraft […]<\/p>\n","protected":false},"featured_media":7567,"menu_order":0,"template":"","meta":{"_acf_changed":false,"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":"","footnotes":""},"area_proyectos":[230],"class_list":["post-6903","proyecto","type-proyecto","status-publish","has-post-thumbnail","hentry","area_proyectos-industry-chp-power-plants-water-treatment-plants-industry-bespoke-solutions"],"acf":[],"_links":{"self":[{"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/proyecto\/6903","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/proyecto"}],"about":[{"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/types\/proyecto"}],"version-history":[{"count":0,"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/proyecto\/6903\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/media\/7567"}],"wp:attachment":[{"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/media?parent=6903"}],"wp:term":[{"taxonomy":"area_proyectos","embeddable":true,"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/area_proyectos?post=6903"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}
SMMR level switches perform the operations required for the filling process and the tank overfilling alarms and protocols. Custom manufacture based on actual needs.
\n\u2022 Probes manufactured from different materials to work with fluids such as gas oil, oil, water, milk, etc.
\n\u2022 Probe with sealed head, can be fastened with 2\u2019\u2019, 11\/2\u2019\u2019 or 1\u2019\u2019 nuts, mounted with aluminum or standardized flange.
\n\u2022 For controlling pumps, solenoid valves, alarms, etc…
\n\u2022 Control box with relays and power supply.<\/p>\n
Pump with self-adjusting blades, with positive movement and constant flow. Silent, robust and high-performance. Particularly recommended for transfer of all kinds of liquid -as long as they are not abrasive nor contain suspended solid particles. Compact pump unit for gas oil pumping. Contains all the elements required for the proper operation of motor pumps in one bench. \u2022 Digital output for incidence control from central position in kit 3, 4 and 6 signals (2-thermal, 2-motors OK, low pressure and spillage). Placing collector trays under certain elements of the installation is recommended. Particularly, equipment that could leak due to its characteristics or during maintenance tasks. Placing a spillage detector for the tray gives the possibility of creating protocols. Constant pressure and flow regulator valve according to consumption variations The next project required automated supply of JET-A1 aircraft fuel for testing engines in bench. In this process, the unloading process of the tanker to the main tank had to be monitored and managed, with the help of an unloading pump. But the main challenge of the project were the operating supply requirements in aircraft […]<\/p>\n","protected":false},"featured_media":7567,"menu_order":0,"template":"","meta":{"_acf_changed":false,"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":"","footnotes":""},"area_proyectos":[230],"class_list":["post-6903","proyecto","type-proyecto","status-publish","has-post-thumbnail","hentry","area_proyectos-industry-chp-power-plants-water-treatment-plants-industry-bespoke-solutions"],"acf":[],"_links":{"self":[{"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/proyecto\/6903","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/proyecto"}],"about":[{"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/types\/proyecto"}],"version-history":[{"count":0,"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/proyecto\/6903\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/media\/7567"}],"wp:attachment":[{"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/media?parent=6903"}],"wp:term":[{"taxonomy":"area_proyectos","embeddable":true,"href":"https:\/\/www.inprord.com\/en\/wp-json\/wp\/v2\/area_proyectos?post=6903"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}<\/span><\/p>\nTRANSFER PUMP<\/span><\/h2>\n
\n\u2022 Blade adjustment is due to three variables. Centrifugal force, fluid pressure and push rods, so losses and turbulence are greatly decreased.
\n\u2022 Adjustable safety valve included in pump body.
\n\u2022 Pump body in cast or stainless steel, based on needs.
\n\u2022 Bench from gray cast iron.
\n\u2022 Three-phase engine with Atex certificate.
\n\u2022 Possibility of 2 rotation directions by placing an inverter.
\n\u2022 The power of the associated motor prevents possible problems at launch with low temperature fuel.<\/p>\n<\/span><\/p>\nPump unit \u201cINPRO\u201d FP GET<\/span><\/h2>\n
\n\u2022 Gear electric pumps with three-phase or mono-phase supply.
\n\u2022 Motor protection IP-55
\n\u2022 System to interrupt no-load operation in case of lack of fuel
\n\u2022 Alternative electronic control management system v
\n\u2022 Vacumeter
\n\u2022 Aluminum filter, Retention valves.
\n\u2022 Safety valve with exhaust line.<\/p>\n<\/span><\/p>\nKerosene Unit<\/span><\/h2>\n
\n\u2022 Launch scheduling kit due to lack of current.
\n\u2022 GSM alarm system via SMS messages or modem connection.
\n\u2022 Line pressure switch for low pressure signal.
\n\u2022 Modifications for adapting tropicalized and ATEX units.
\n\u2022 Spill collector trays with infrared detectors.
\n\u2022 There are supply system versions for other fluids such as light fuel, methanol, gasoline, etc…<\/p>\n<\/span><\/p>\nCOLLECTOR TRAY WITH SPILLAGE DETECTOR<\/span><\/h2>\n
\n\u2022 Furnace-painted plate tray with the appropriate size for each circumstance.
\n\u2022 Spillage detector in the control panel and detection probe. Infrared optical sensor for oil and water, conductivity sensor for water or both, mounted on the same probe.
\n\u2022 Standard 1.5 m probe.
\n\u2022 The control unit of the detector is mounted in a box with impact-resistant plastic cover. The control unit contains two voltage free relays, one for commuting and the other one usually open.<\/p>\n<\/span><\/p>\nPRESSURE REGULATOR VALVE<\/span><\/h2>\n
\n\u2022 For gas oil, lubricant and hydraulic oils.
\n\u2022 Maximum temperature of the fluid: 250\u00baC.
\n\u2022 Hydraulic cast iron. Piston, needle and tempered steel spring.<\/p>\n<\/span><\/p>\n","protected":false},"excerpt":{"rendered":"